Specialty Car Parts Canada

"Your Canadian Source for HOT DROP IN ENGINES" 

Bolt Them in - Plumb Cooling and Fuel - Hook up the Electrics - Start it up!

Choose your Weapons below!

Engine Department

Note -  On all Engines Freight charges may apply  - depending on your location. We will always try to eliminate this nuisance factor, but do reserve the right to charge freight

 

275HP 302 Cu. In

275HP Hot Drop in - Ready to run 302                          Carbureted Engine Package

If your looking for an Engine with better than stock HP, good driveability  and excellent acceleration, -  without blowing the budget completely out of the water this would be your choice. Over time dress it up with Cobra valve covers and air cleaner but as delivered a very pretty and powerful package. Engine includes everything listed below Needs an Alternator and brackets to complete.

*7.63 Lbs/HP

(*assumes a 2100 Lb Cobra)

Includes all of the following

  • Blueprinted machined 302 Roller Late Style  Block

  • Nodular Cast Iron Crankshaft, deburred and Micropolished

  • Hyperuetectic 9.5 to 1 Federal Mogul Pistons

  • Sealed Power Moly Rings

  • Heavy Duty Double Roller Dynagear Timing Set

  • Steel Roller HO Camshaft Power Range (Idle to 5500 RPM)

  • Federal Mogul Trimetal Bearings

  • New Cast Iron 65cc cylinder heads with new valves, locks, retainers, seals and HD Springs

  • New Hardened Pushrods

  • Stamped Steel 1.6 to 1 ratio Roller Tip Rockers  

  • New Melling  Oil pump

  • Complete Fel-pro Gasket set

  • Factory Replacement Harmonic Balancer

  • New Flexplate for Automatic Trans. 

  • (Std. Trans. Flywheel add $195.00)

  • Oil pan, Timing cover and Chrome Valve Covers

 

  • Edelbrock 650 cfm 4 barrel Carburetor with electric choke

  • Edelbrock Performer Dual Plane Intake Manifold

  • New high flow Water pump and Fuel Pump

  • Electronic Ignition Distributor with 45,000 voltage Coil Pak

  • New Spark plugs and 8mm Silicone Wires

  • New Thermostat Housing

  • Chrome Air Cleaner

  • PCV Ventilation System

  • New Fuel Lines and Gas Filter

  • Ignition Timing Set, Carburetor fully adjusted

  • Hot Run tested and dialed in

  • Video Footage taken with your engine running in our test Stand

  • Packaged and Crated

  • Installation Video Included

 

       Total Cost for This Engine As a Long Block  

                       (Add your own  Distributor, Water pump, Alternator, Fuel Pump Manifold, Carb, Air Cleaner etc)

$3,995.00

Click HERE to Order

Total Cost for This Engine As a Hot Drop In

Note - Requires Alternator and Brackets to Complete

$6495.00

Click HERE to Order
 
350HP ready to run - Hot Drop In 302

350HP 302 Cu. In

                                  Carbureted Engine Package

If your taste runs to  an engine with that distinctive lumpy Idle and a bigger kick in the back when you step on it you might want to go with this option. At 350 HP in a 2100 Lb car that's serious acceleration! 

*6.0 Lbs/HP

(*assumes a 2100 Lb Cobra)

Includes Everything Listed Below

  • PRECISION MACHINED 302 ROLLER BLOCK
  • NODULAR CAST IRON CRANKSHAFT
  • SHOT PEENED & STRESS RELIEVED CONNECTING RODS WITH 190,00 PSI Hardened BOLTS
  • Hypereutectic Federal Mogul  9.5 TO 1 COMPRESSION
  • SPEED PRO Chrome Moly PISTON RINGS
  • 3 PIECE STEEL ROLLER STYLE TIMING CHAIN
  • HYDRAULIC STEEL ROLLER CAMSHAFT DELIVERS MID-RANGE HORSE POWER AND Great LOW END TORQUE
  • NEW MELLING OIL PUMP AND SCREEN
  • EDELBROCK RPM ALUMINUM HEADS 60cc COMBUSTION CHAMBER with Bronze Guides
  •  STAINLESS STEEL SWIRL POLISHED INTAKE VALVES
  •  STAINLESS STEEL SWIRL POLISHED EXHAUST VALVES
  • HARD SEATS FOR UNLEADED OR REGULAR FUEL
  • HEAVY DUTY 1.45 DIAMETER VALVE SPRINGS, 7 DEGREE LOCKS
  • CHAMPION SPARK PLUGS GAPPED AND INSTALLED
  • COMP CAMS ROLLER TIP ROCKERS
  • NEW CHROME FRONT SUMP 5 QUART OIL PAN
  • TIMING CHAIN COVER WITH SCALE
  • CHROME BAFFLED VALVE COVERS
  • HEAVY DUTY AUTOMATIC  FLYWHEEL 
  • NEW 4 BARREL 650 CFM  EDELBROCK AVS CARBURETOR WITH ELECTRIC CHOKE
  • ELECTRONIC IGNITION DISTRIBUTOR.  1 WIRE HOOK-UP 45,000 VOLT COIL PAK
  • 45 DEGREE WATER TEMPERATURE THERMOSTAT HOUSING
  • 8MM ACCEL SILICONE WIRES
  • NEW CHROME THERMOSTAT HOUSING
  • NEW FUEL AND WATER PUMP
  • CHROME DIP TUBE AND DIPSTICK
  • NEW CHROME MOROSO AIR CLEANER WITH PCV VENTILATION SYSTEM
  • NEW FUEL LINES AND GAS FILTER
  • HOT RUN TESTED INCLUDES SETTING INITIAL AND FULL TIMING ADVANCE
  • VIDEO FOOTAGE SHOWN OF YOUR ENGINE IN TEST STAND
  • BALANCED, BLUE PRINTED, ASSEMBLED BY ASE TECHNICIANS

Total Cost for this engine $7100.00

Note - Requires Alternator and Brackets to Complete

Click HERE to Order 
                                                                    373HP 302 Cu. In

                                  Carbureted Engine Package

If your looking for borderline brutal this is the entry point!   This is even faster than the previous option!  Engine includes everything listed below. As with previous engines need to add an alternator and brackets.

*5.6 Lbs/HP!

(*assumes a 2100 Lb Cobra)

Includes everything listed below

  • Blueprinted machined 302 Roller version Block

  • Nodular Cast Iron Crankshaft, deburred
     and micro polished

  • Shot peened hardened connecting rods
     with 190,000 psi bolts

  • Hyperuetectic 10 to 1 Federal Mogul Pistons

  • Sealed Power Chrome Moly Rings

  • Heavy Duty Double Roller Dynagear Timing Set

  • Edelbrock Performer RPM Hydraulic Roller Camshaft

  • Clevite Street Racing Bearings

  • Aluminum fast burn  Edelbrock RPM cylinder heads w/ stainless steel valves, hardened valve locks, chromemoly retainers & HD Valve Springs

  • Chrome Moly  pushrods

  • 1.6 to 1  Ratio Roller Tip Rockers

  • New Melling Oil pump

  • Complete Fel-pro Gasket set

  • New Harmonic Balancer

  • New Flexplate for Automatic Trans.
     (Standard Flywheel add $175)

  • New Oil pan, Timing cover and Chrome Baffled Valve Covers

  • Edelbrock Performer RPM Dual Plane Intake

  • 4 Barrel 650 Cfm  Edelbrock Thunder Series Carb. w/ Electric Choke  

  • New High Flow Water pump 

  • New Fuel Pump and fuel lines

  • Electronic Pertronix Ignition Distributor & 45,000 volt coil w/ Vacuum advance

  • New Champion Spark plugs gapped and installed

  •  8mm Accel Silicone Wires

  • New Thermostat Housing

  • Chrome Air Cleaner

  • PCV Ventilation System

  • New Fuel Lines and Gas Filter

  • Ignition Timing Set, Carburetor fully adjusted

  • Hot Run tested and dialed In place

  • Video Footage with engine running in our test Stand for your personal record

    •

Total Cost for This Engine As a Long Block  

 (Add your own  Distributor, Water pump, Alternator, Fuel Pump Manifold, Carb, Air Cleaner etc)

$5,195.00

Click HERE to Order

Total Cost for This Engine As a Hot Drop In

Note - Requires Alternator and Brackets to Complete

$7695.00

Click HERE to Order

 

400HP 351 Cu. In

                                  Carbureted Engine Package

          *5.25 Lbs/HP

                  (*assumes a 2100 Lb Cobra)

                         This is the engine for those that think too much power is ALMOST enough!

            Includes Everything Listed Below

   
  • PRECISION MACHINED 351W BLOCK
  •  MICRO-POLISHED & DEBURRED NODULAR CRANKSHAFT
  • SHOT PEEN HARDENED & STRESS RELIEVED CONNECTING RODS WITH 190,00 PSI ARP BOLTS
  • HYPEREUTECTIC  HEAVY DUTY PISTONS 9.7 TO 1 COMPRESSION
  • SPEED PRO PISTON RINGS
  • 3 PIECE STEEL ROLLER STYLE TIMING CHAIN
  • H.O. CRANE CAMSHAFT DELIVERS MID-RANGE HORSE POWER AND EXCELLENT LOW END TORQUE
  • NEW MELLING OIL PUMP AND SCREEN
  • EDELBROCK RPM ALUMINUM HEADS 60cc COMBUSTION CHAMBER
  • STAINLESS STEEL SWIRL POLISHED INTAKE VALVES
  • STAINLESS STEEL SWIRL POLISHED EXHAUST VALVES
  • COMP CAMS MAGNUM ROLLER 1.6 RATIO ROCKERS
  • HARD SEATS FOR UNLEADED OR REGULAR FUEL
  • HEAVY DUTY 1.45 DIAMETER VALVE SPRINGS, 7 DEGREE LOCKS
  • NEW HEAVY DUTY CHROME MOLY PUSH RODS
  • NEW CHROME FRONT SUMP 5 QUART OIL PAN
  • ALUMINUM TIMING CHAIN COVER WITH SCALE
  • FORD COBRA BLACK WRINKLED ALUMINUM VALVE COVERS
  • HEAVY DUTY SFI APPROVED STANDARD  FLYWHEEL 
  • NEW EDELBROCK PERFORMER RPM DUAL PLANE INTAKE MANIFOLD
  • NEW 4 BARREL 650 CFM EDELBROCK CARBURETOR WITH ELECTRIC CHOKE
  • HIGH VOLTAGE ELECTRONIC PERTRONIX BILLET DISTRIBUTOR AND COIL
  • 8 MM ACCEL SILICONE WIRES
  • NEW CHROME THERMOSTAT HOUSING
  • NEW FUEL AND WATER PUMP
  • CHROME DIP TUBE AND DIPSTICK
  • NEW BLACK WRINKLED COBRA OVAL AIR CLEANER WITH PCV VENTILATION SYSTEM
  • NEW FUEL LINES AND GAS FILTER
  • HOT RUN TESTED INCLUDES SETTING INITIAL AND FULL TIMING ADVANCE
  • VIDEO FOOTAGE SHOWN OF YOUR ENGINE IN TEST STAND
  • CHROME ONE WIRE HOOK UP 100 AMP ALTERNATOR
  • MARCH POLISHED PULLEYS AND CHROME BRACKETS
  • NEW V-BELT INSTALLED AND TENSION ADJUSTED
  • BALANCED, BLUE PRINTED, ASSEMBLED BY ASE TECHNICIANS
 
 
Complete and ready to Run as delivered!
Highlighted Areas show difference from other complete engines offered 

Total Cost for This Engine $8,650.00

Click HERE to Order 

 

                  435HP 351 Cu. In

                                  Carbureted Engine Package

*4.82 Lbs/HP

                                     (*assumes a 2100 Lb Cobra)

                         This is the engine for those that think too much power is ALMOST enough and live for the adrenalin rush that this engine can produce!

            Includes Everything Listed Below

Not Exactly as Shown, does not come with Cobra Air Cleaner or Valve Covers

Comes Complete with

  • Blueprinted machined 351w Block

  • Nodular Iron Crankshaft, deburred
     and micro polished

  • Shot peened hardened connecting rods
     with 190,000 psi bolts

  • Power Forged 10 to 1 Flat Top SRP Pistons

  • Sealed Power Chrome Moly Rings

  • Heavy Duty Double Roller Dynagear Timing Set

  • Comp Cams Hydraulic Roller Camshaft (Power Range 2000-6500 RPMs)

  • Clevite Street Racing Bearings

  • Aluminum Fast Burn Edelbrock RPM Heads w/ Port matched intake Runners

  • 2.02 x 1.60 Stainless steel Polished valves, Hardened valve locks chrome
      moly retainers and High Intensity Valve Springs

  • Chrome Moly Comp Cam pushrods

  • 1.6 to 1 Crane True Roller Rockers

  • New Melling Oil pump

  • Complete Fel-pro Gasket set

  • New Heavy Duty Harmonic Balancer

  • New Flexplate for Automatic Trans.
     (Standard Steel Billet Flywheel add $300)

 

  • New Polished Oil pan, Alum. Timing cover & Chrome Baffled Valve Covers

  • Edelbrock Air Gap Dual Plane Intake

  • Edelbrock 650 cfm 4 barrel Carburetor with electric choke

  • New High Flow Water pump 

  • New Fuel Pump and fuel lines

  • Billet Electronic Ignition Distributor &  high voltage coil with Vacuum advance

  • New Champion Spark plugs gapped and installed

  •  8mm Accel Silicone Wires

  • New Thermostat Housing

  • Chrome Air Cleaner

  • PCV Ventilation System

  • New Fuel Lines and Gas Filter

  • Ignition Timing Set, Carburetor fully adjusted

  • Hot Run tested and dialed In place

  • Video Footage with engine running in our test Stand

  • Packaged and Crated for Shipment

 

Requires Alternator and related brackets to complete!

Total Cost for This Engine $9,450.00

Note - Requires Alternator and Brackets to Complete

Click HERE to Order  

           530HP 427 Cu. In

                                  Carbureted Engine Package

*3.96 Lbs/HP

                                     (*assumes a 2100 Lb Cobra)

When you absolutely, positively have to be the fastest on your block (or County) this  absolutely, positively has to be your  weapon of choice!

 Engine comes complete and ready to run with......

  • New Dart Iron Eagle 351W Block Machined to accept Stroker Crankshaft 4.250 Bore.

  • New Forged Steel Scat Crankshaft 4.100" Stroke

  • H Steel Beam connecting rods 6.200" inch in Length
     with 190,000 psi ARP bolts

  • Power Forged SRP  10.5 to 1 Compression Flat Top Pistons

  • J & E Chrome Moly Rings

  • Heavy Duty Double Roller Dynagear Timing Set

  • Xtreme Energy Hydraulic Roller Camshaft

  • Clevite H Series Bearings

  • Aluminum fast burn  Edelbrock Victor Jr. cylinder heads

  • 2.05 X 1.60 stainless steel valves, hardened valve locks, chrome moly retainers and HD Valve Springs

  • Chrome Moly  pushrods

  • 1.6 to 1  Ratio Comp Cams Pro Magnum Roller Rockers

  • New Melling High Volume Oil pump

  • Complete Fel-pro Gasket set

  • New Harmonic Balancer

  • New Standard Flywheel SFI approved

  • New Canton Large Capacity Oil pan, Timing cover and Cobra Baffled Valve Covers

  • Edelbrock Victor Jr.Single Plane Intake

  • Holley Double Pumper 800 cfm  4 barrel Carburetor

  • New High Flow Aluminum Water pump 

  • New High Flow Fuel Pump

  • Electronic MSD Ignition Distributor &  45,000 volt coil with Vacuum advance

  • New Champion Spark plugs gapped and installed

  •  8mm Accel Silicone Wires

  • New Thermostat Housing

  • Cobra Oval Air Cleaner

  • PCV Ventilation System

  • New Fuel Lines and Gas Filter

  • Ignition Timing Set, Carburetor fully adjusted

  • Hot Run tested and dialed In place

  • Video Footage with engine running in our test Stand for your personal record

  • March Performance Pulley Kit with 100 Amp Chrome Alternator, Brackets and Belt Installed

  • Packaged and Crated for Shipment

                        Total Cost for This Engine $18,950.00

                                       Click HERE to Order 

S                                                             Still not what your looking for? Try entering it into the search Box below!

  
Google

 Links | Contact | About Us

Page Last Updated 07/07/2007

Copyright 2007 by ABANAL Specialty Car Parts Canada Ltd